BMW E30 325i auto to manual 6-speed ZF GS6-37DZ transmission swap

A typical E30 325i automatic transmission swap to manual with the Getrag 260

A typical manual transmission swap uses the 5-speed Getrag 260 transmission from a manual E30.
Here is the list of the parts that are required for a swap:

  • Transmission input shaft seal
  • Engine rear main seal
  • Transmission
  • Transmission oil
  • Transmission crossmember 23711176574
  • Transmission mounts 23711175939 x2
  • Transmission mount nuts 07119905515 x4
  • Washer 33311108205 x2
  • Washer 07119904115 x2
  • Shifter assembly
  • Selector rod | Shift link w/washers and clips
  • Shift handle
  • Shift knob and emblem
  • Nylon cup and bushing
  • Shift lever insulating rubber boot
  • Shift lever leather boot
  • Lock pin for support arm
  • Bushing mounting nut
  • Transmission to block bolts (set, you can reuse the bolts that came off your auto)
  • Giubo bolts
  • Giubo
  • Manual driveshaft
  • Center bearing assembly
  • Reverse light switch
  • M/T reverse lamps wiring harness BMW 23141220263
  • Clutch cruise control switch and wiring
  • Flywheel
  • Flywheel spacer plate
  • Flywheel bolts x8 (need new)
  • Throwout bearing
  • Clutch/Pressure Plate assembly
  • Clutch fork
  • Clutch fork bearing
  • Clutch master cylinder
  • Clutch master fluid line connector
  • Clutch slave cylinder
  • Clutch hardline
  • Firewall grommet
  • Clutch soft line
  • Brake pedal 35211154729
  • Clutch pedal 35311156838
  • Clutch and brake pedal rubber pads 35211108634
  • Hex bolt for the pedals M10x175 07119912721

The most expensive parts are the Getrag 260, manual driveshaft, shifter and selector rod, flywheel, and clutch. It’s very difficult to find a Getrag 260 that doesn’t need a rebuild. BMW sells a refurbished one for $3,500.

If you have to change so many parts, isn’t it better to install a newer 6-speed transmission with its driveshaft, shifter, clutch, differential, and linking parts?

GS6-37DZ transmission

A newer one can be the European diesel transmission GS6-37DZ. This swap was pioneered by Wanganstyle.

This article describes only the Project Research stage. I’m trying to collect as much information as possible. I don’t know what will work and what won’t.

The GS6-37 is a 6-speed manual transmission manufactured by ZF Friedrichshafen AG and Getrag. It is designed for longitudinal engine applications and is rated to handle up to 370 newton metres (273 lbf⋅ft) of torque.

Gear ratios

Gear ratios for Getrag 260
1 2 3 4 5 R
3.83 2.20 1.40 1.00 0.81 3.71
Gear ratios for diesel GS6-37DZ
1 2 3 4 5 6 R
5.14 2.83 1.79 1.26 1.00 0.83 4.64
Gear ratios for gasoline GS6-37BZ
1 2 3 4 5 6 R
4.350 2.496 1.665 1.234 1.000 0.851 3.926

Differential

Which differential ratio is the best?

  • The acceleration in the 2, 3, 4 gears should be similar to the Getrag 260 + a 4.10 or 3.73 differential.
  • The 6th gear should be good for low-RPM freeway cruising.
  • The 1st gear should be usable.

The Getrag 260 with a 4.10 differential compared to the GS6-37DZ with a 3.15 differential:

Differential ratios 4.1 3.15

The Getrag 260 with a 3.73 differential compared to the GS6-37DZ with a 3.07 differential:

Differential ratios 3.73 3.07

It’s possible to find Z3 3.07 and 3.15 medium 188mm differentials. They have Torsen LSDs and require little maintenance for regular driving. They are more modern and have few miles as the regular Z3 was a weekend car. The Z3M had a 3.23 clutch-type LSD differential.

Getrag 260 and GS6-37DZ bellhousing comparison

Looking at the different variants of the GS6-37DZ transmission, only the earlier variants GS6-37DZ — THES (23007562730) and GS6-37DZ — TJEM (23007565194) can be used.

Compatible transmissions were installed with the M47 engine:

GS6-37DZ — TJEM

  • BMW E87 (118d, 120d)
  • BMW 320Cd E46
  • BMW E90/E91 (318d (M47N2), 320d (M47N2))
  • BMW E60/E61 (520d)
  • BMW E60 LCI/E61 LCI (520d (M47N2))

GS6-37DZ — THES

  • BMW 120d E87
  • BMW E46 (320Cd/td, 320d (M47N))
  • BMW E90/E91 (320d M47N2)
  • BMW E60/E61 (520d)

The newer versions of the GS6-37DZ (TJEF, TJEJ) that came with the engine N47 have the starter protrusion at the bottom, not at the top. They are not compatible.

gs6-37DZ-TJEJ

The main advantage of the GS6-37DZ (D – diesel) over its sibling GS6-37BZ (B – benzin, petrol, gasoline) is the slant(tilt) degree of 20°. The slant degree of the M20 engine in the 325i is the same. The engine doesn’t stand vertically to save on the height. The GS6-37BZ has the slant degree of 30° – it’s compatible with the M30, M50, etc.

Getrag 260 and GS6-37DZ bellhousing comparison

As you can see, the GS6-37DZ has more bellhousing holes than the Getrag 260: 2 at the bottom and 1 pin at the top.

The transmission will be mated with the BMW M20 engine. The top pin interferes with the starter. But the M20 starter won’t probably work with the GS6-37DZ flywheel, so it’ll be replaced anyway.

BMW M20 engine rear

The bottom part of the M20 engine can be disconnected. It’s called the Bowl reinforcement (11141286342). An additional hole can be drilled and tapped in it, but there is no casting for it in the back of the reinforcement. Maybe, a nut can be used.

bowl_reinforcement

Transmission drive shaft differences

The driveshaft in the Getrag 260 has 10 splines, the driveshaft of the GS6-37DZ has 22 splines. So, a clutch disk should have 22 splines too.
The driveshaft in the Getrag 260 is longer and its pilot bearing is inserted into the crankshaft of the engine.
The driveshaft in the GS6-37DZ is shorter and its pilot bearing is in the flywheel.

Rear transmission mount brace (cross member)

The GS6-37DZ is mounted differently. The top (22316760303) E90 Transmission supporting bracket is available. Then, the mounting style and dimensions should be similar to the 6-speed Getrag 420G, for which some companies create braces.

GS6-37DZ rear mounting brace

A custom bracket for a 6-speed transmission in a BMW E30

Drive Shaft

The automatic E36 M3 driveshaft

The GS6-37DZ is 635 mm long. It is 120 mm longer than the Getrag 260. The automatic transmission ZF HP4-22 is 685 mm long.
The length of the drive shaft for the GS6-37DZ must be close to 1367 mm.

gs6-37bz dimensions

The E36 M3 automatic drive shaft (26112228212) should be compatible with its length of 1346 mm. It’s about 20 mm short.

E36 M3 auto drive shaft 26112228212

Also, the European E36 automatic drive shaft (26111227441) should be compatible too with its length of 1345 mm.

It seems that many 4-bolt E36 drive shafts have the same rear half. It’s only the front half that has different lengths. Both u-joints are located in the rear half, and they wear out. The front half is just a pipe with connectors.

Some people indicate that the manual Z4 front part(26117514468) can be used with the rear E36 part to provide the perfect length.

The M3 giubo (26112226527) is 96mm in diameter, 35 mm wide, and it is connected using M12 bolts.

The drive shaft center support mount must be from the E30 (26121226723). Probably, it should be mounted backwards.

The front section of the E46 320d driveshaft + the rear section of the E30 rear driveshaft

The rear section of all E30 driveshafts is the same, so a good automatic E30 driveshaft can be used.

The front section must come from a European e46 320d produced from 03/2003 (26117523929). The 6-speed E46 330i and M3 driveshafts are not compatible.

e46 320d 26117523929 + e30 drive shaft

e46 320d drive shaft 7523929

Shifter

The shifter carrier and selector rod for this conversion must be custom.

Shifter carrier and Selector rod

Zionsville BMW E36 6 Speed Conversion Shift Arm Support Bracket.
Zionsville shifter carrier

A longer shifter carrier can be shortened and welded.
gs6-37 Shifting carrier welded

Here is a shifter carrier and selector rod for the E36 + GS6-37BZ. It should be compatible, too.
E36 GS6-37BZ

Flywheel and Clutch

The LuK dual-mass flywheel.
LuK DMF053 twin-mass flywheel

The original M20 flywheel.
M20 flywheel

These items should work:

There are aftermarket flywheel and clutch kits.
Clutch Masters 2003-2006 : 3.0L E46 (6-Speed)

Clutch Slave Cylinder

The master clutch cylinder is from the E30. The slave clutch cylinder is from the E36 325i(21521159045). There should be other compatible clutch cylinders.

Starter

The starter from the E46(12412354693) is compatible with the E46 flywheel.

The Bosch SR0448N from the E46 has the threaded holes for the bolts, no E30-style nuts will be needed.

The E30 starter(12411726504) specifications:
Rated Power [kW]: 1,4
Voltage [V]: 12
Number of Teeth: 9
Rotation Direction: Clockwise rotation
Number of mounting bores: 2
Flange Ø [mm]: 76
Number of Thread Bores 0
Plug Type ID: M6
Clamp: M8
Length 3 [mm]: 25
Length [mm]: 184.21

The E46 starter(12412354693) specifications:
Rated Power [kW]: 1,4
Voltage [V]: 12
Number of Teeth: 9
Rotation Direction: Clockwise rotation
Number of mounting bores: 3
Flange Ø [mm]: 76
Number of Thread Bores: 2
Plug Type ID: M6
Clamp: M8
Length 3 [mm]: 23
Length [mm]: 173.21

Reverse Switch

The E30 reverse switch(23141354071) has a correct connector.

Lube and Oil

The transmission splines must be lubed.

Rebuilding the GS6-37DZ transmission

The transmission bellhousing can be opened using this crude technology.
It seems that the bellhousings of the GS6-37DZ and GS6-37BZ can be exchanged to get the gasoline engine gear ratios.

gs6-37bz bellhousing open

In addition to the new seals and new bolts, these bearings are required for a rebuild:

  • 2 bearings for the input and main shafts NSK 35TM10-A-1CG28U01 (BMW 23111224806) 35x80x20mm
  • 1 bearing for the main shaft by ZF. 1833728 IC 32272-MB90A IC 0735298254 ZF 1833728 DAF, 5001847341 DAF 42535016 IVECO 5001847341 IVECO 8869673 IVECO, 8869673EB12-6460 IVECO 32272-MB90A NISSAN 322754716R RVI, 50 01 847 341 RVI 23×40,40x21mm
  • 1 bearing for the lay shaft SKF BA2B 633910 C (BMW 23111224808) 29.8x67x31mm
  • 1 bearing INA 712 0613 10 (INA F-223773) 27x44x23.2mm

NSK 35TM10-A-1CG28U01, SKF BA2B 633910 C(23111224808)

NSK 35TM10-A-1CG28U01 (BMW 23111224806)

SKF BA2B 633910 C (BMW 23111224808)

bearing INA 712 0613 10 (INA F-223773)

Schematics of the GS6-37DZ

gs6-37dz schematics

10 thoughts on “BMW E30 325i auto to manual 6-speed ZF GS6-37DZ transmission swap

  1. Hello! Love this page, it’s full of great information. Are you able to give the lengths of the modified shifter carrier and selector rod?

    I have a shifter carrier that needs to be shortened but I don’t have it in the car yet to check the length. Thank you!

    1. I haven’t finished the swap yet. I’m more into electronics recently.

      I added a photo of a shifter carrier + rod for E36 + GS6-37BZ.
      They are 140 mm and 96 mm. People say the dimensions are pretty close to what they used.

      Though, the rod is straight, and it may not work will very long shifters.

  2. I just wanted to say that you have done a fantastic research and you helped me a lot with figuring out things. Well done!
    I used a dual mass flywheel to single mass flywheel conversion kit which is available on Ebay. It’s worth mentioning this option in your wiki.

  3. Hi guys,
    undergoing similar swap of this box into an e30 but its a K-swap K24, -love the information
    where can I order that e36 carrier shifter mount please

  4. Thanks very much for the detailed write-up. Much appreciated. I am looking at doing the same swap but with a Single Mass flywheel conversion.

    I saw someone’s YouTube video who used this kit: NTY NZS-BM-004. I see your DMF is used on the M54 engines whereas the kit I’m looking for is specified as an N47 D20 kit.

    Do you know if the flywheels are interchangible between the M54 and N47 engines?

    Just want to make sure before I purchase :-)

    1. No, I don’t have information about it.

      I just followed the instructions from people who say that an M54 flywheel should work with changing the starter. This engine came with the GS6-37BZ transmission in the E46. You can ask the question in E46 forums.
      There are single-mass flywheels for the M54 engine.

Leave a Reply to Nader Sh Cancel reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>